Specification > Performance

Performance   |   Standard Height & Width   |   Standard Fixings   |   CAD Drawings

JX Product Concept

Jalousie louvre frame, 63 mm module

• Square-cut assembled fixed frame.
• Opening louvres in curved aluminium or glass at 135 mm intervals.
• Hinging and protection ensured by overlapping polyamide end caps enabling opening to 80°.
• Weatherproofing ensured by marine-quality EPDM gaskets or polyethylene brush gasket.
• Stainless steel screws.
• Operation by lever handle, turn handle or knob
• Driver rods in Zamac alloy.

Options

• Installation on single inside sill.
• Installation on inside sill with self locating system.
• Fly screen, removable for cleaning.
• Reinforced security by 5 mm Ø cross rod.

6.6 mm laminated glass louvres intrusion proof frame

According to level 2 norm EN 1627.
Tests CNPP MD050016 and MD050017 10/03/05

Loosening of glass louvres bearer

Pull force upper than 200 daN on bearers without loosening of louvres.
Test no. Q-0305-01

Sunlight ageing

On end caps and drivers, after 300 hours in compliance with standard NF T51-056, no noticeable change in characteristics.

CSTB test no. 01-0020

FEATURES

Designed for cyclonic areas
NATA tested and approved
Water penetration to 400pa
N5 rated -3300kpa
Sealed for Air conditioning
6mm glass blade up to (900mm wide in cyclonic Regions)
Louvres available in Glass & Aluminium
No surround frame required
Exceptional overall appearance
Louvre Blade Support section is a security bar
External security bars & grills not required
Sound proof testing. Sound fading Rate 23db

Louvre blade centres is 135mm.
Louvres open to the outside of the window. No interference to curtains or blinds
Internal Screens easy to remove and clean
All Aluminium & stainless steel construction
Louvre blades lock in 4 opening positions (secure)
6mm glass louvres
Aluminium Louvre blades are one piece and cannot be removed
Requires 200KG pull out to remove louvre blades
Louvres seal to EDPM seals on all 4 sides
Toughened glass required from floor to 800mm
Jamb size 63mm * 42mm

Material

• Aluminium extrusion to be 6060T6
• Operating mechanism to be Renee plastic moulded or Stainless Steel lever handles optional with Aluminium Link Bar.
• Standard surround frame to be 63mm*42mm powder coated extrusions/ clear / bronze anodised

Glass louvre blades

• To be 113mm * 6mm with exposed long edge to be arissed and flat polished to comply with AS 2047.

Aluminium Blades

• To be extruded one piece powder coated finish/ clear/ bronze anodised

Blade Seals

• JX Louvre blades to close against EDPM seals fitted to both louvre jamb sections with glass filled moulded end fittings. Long edge of blade closes to EDPM seal fitted to top edge of security blade holder.

Standard operating mechanism

• To be lever handle with 4 locking positions from fully closed to fully open (80 Degrees). Lever handle is available in moulded nylon or Polished stainless steel (Suitable for Map Rod, manual remote control or 12V electronic operation with water sensing and reopen after rain facility or other sensing devices including attachment to fire protection systems which fully open the louvres and lock until the fire alarms are reinstated
• NB Motor drives are fitted to the Jalousie frame and may only be practical in out of reach areas or for use by the disabled
• Refer chart for the number of handles required)

Insect Screen

• To be fitted internally into surround frame sections. Plastic or other types of turn clips are not to be used.

Blade Lengths

• 6mm glass, aluminium extruded or timber blades to a maximum opening size of 900mm requiring a water penetration rating to 400pa and design wind pressure up to 3300 kpa.

Additional security

• Each security blade holder to be fitted with 6mm stainless steel bar.

Balustrade Code

• All louvre units shall conform to balustrade code and shall have a maximum space of no less than 115mm between.